电脑技术学习

CISCO7200路由器MultiChannel配置介绍

dn001

  1.Controller Configuration Examples控制器配置举例
  
  The following example shows a typical controller configuration for
  the multichannel E1/PRI port adapter on a Cisco 7200 series or
  Cisco uBR7200 series router:
  
  router> enable
  router# configure terminal
  router(config)# controller E1 1/0
  router(config-controller)# framing crc4
  router(config-controller)# linecode hdb3
  router(config-controller)# clocksource internal
  router(config-controller)# channel-group 0 timeslots 1-31
  router(config-controller)# description ppp channel 5
  router(config-controller)# shutdown
  router(config-controller)# ^Z
  
  2.Interface Configuration Examples接口配置举例
  The following example shows a typical interface configuration for
   the multichannel E1/PRI port adapter on a Cisco 7200 series or
  Cisco uBR7200 series router:
  
  router> enable
  router# configure terminal
  router(config)# interface serial
  router(config)# interface serial 4/1:0
  router(config-if)# encapsulation ppp
  router(config-if)# description ppp channel 5
  router(config-if)# no shutdown
  router(config-if)# ^Z
  
  3. Configuring Multichannel E1 Interfaces 配制多通道E1接口
  The channel groups must be mapped before the multichannel E1/PRI
  controller can be configured. The following are controller commands
  used to map the channel group (the default variable is listed first):
  
  controller E1 port-adapter-slot number/port-number (for Cisco 7200
  series router)
  clock source [line internal]
  linecode [ami hdb3]
  framing [crc4 no-crc4]
  loopback [diagnostic local {payload line}]
  shutdown
  channel-group number timeslots list
  Number is the channel group 0 to 30.
  list is a number between 1 and 31. You can enter timeslots individually
   and separate them by commas, or enter them as a range separated by
   a hyphen (for example, 1-3, 8, 9-18). Timeslot 0 is an illegal
  configuration.
  
  4.常用调试命令
  show version or show hardware
  Displays system hardware configuration, the number of each interface
  type installed, Cisco IOS software version, names and sources of
  configuration files, and boot images
  show controllers
  Displays all the current interface processors and their interfaces
  show diag slot
  Displays types of port adapters installed in your system and
  information about a specific port adapter slot, interface processor
  slot, or chassis slot
  show interfaces type 0 or 1/
  interface-port-number
  Displays status information about a specific type of interface (for
   example, serial) on a Catalyst RSM/VIP2
  show interfaces type mod_num/bay/port
  Displays status information about a specific type of interface (for
  example, serial) on a Catalyst 6000 family FlexWAN module
  show interfaces type 3/interface-port-number
  Displays status information about a specific type of interface (for
   example, serial) in a Cisco 7120 series router
  show interfaces type 4/interface-port-number
  Displays status information about a specific type of interface (for
   example, serial) in a Cisco 7140 series router
  show interfaces type port-adapter-slot-number/interface-port-number
  Displays status information about a specific type of interface (for
   example, serial) in a Cisco 7200 series router
  show interfaces type 1/interface-port-number
  Displays status information about a specific type of interface (for
  example, serial) in a Cisco uBR7223 router
  show interfaces type 1 or 2/interface-port-number
  Displays status information about a specific type of interface (for
  example, serial) in a Cisco uBR7246 router
  show interfaces type interface-processor-slot-number/port-adapter-
  slot-number/interface-port-number
  Displays status information about a specific type of interface (for
   example, serial) on a VIP2 or VIP4 in a Cisco 7000 series or Cisco
  7500 series router
  Router# show interfaces serial 3/1/0
  show protocols
  Displays protocols configured for the entire system and for specific
  interfaces
  show running-config
  Displays the running configuration file
  show startup-config
  Displays the configuration stored in NVRAM
  
  5. show Cisco 7200 Series and Cisco uBR7200 Series Routers
  下列显示72的SHOW结果!
  
  Following is an example of the show interfaces serial port-adapter-
  slot-number/port-number:channel-group command for Cisco 7200 series
  and Cisco uBR7200 series routers. It shows all of the information
  specific to the first multichannel E1/PRI port (port 0) in port
  adapter slot 2, channel group 1:
  
  Router# show interfaces serial 2/0:1
  
  Serial2/0:1 is up, line protocol is up (looped)
   Hardware is Multichannel E1
   Internet address is 1.6.0.1/30
   MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, rely 255/255, load
  1/255
   Encapsulation HDLC, loopback not set, keepalive set (10 sec)
   Last input 00:00:07, output 00:00:07, output hang never
   Last clearing of "show interface" counters never
   Input queue: 0/75/0 (size/max/drops); Total output drops: 0
   Queueing strategy: weighted fair
   Output queue: 0/64/0 (size/threshold/drops)
     Conversations 0/1 (active/max active)
     Reserved Conversations 0/0 (allocated/max allocated)
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
     87 packets input, 6521 bytes, 0 no buffer
     Received 87 broadcasts, 0 runts, 0 giants
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     87 packets output, 6521 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
     1 carrier transitions
   no alarm present
   Timeslot(s) Used:1-31, subrate: 64Kb/s, transmit delay is 0 flags